TLHP is open and ships orders!


Speaker Audax HM130Z4, 8+8 ohm, 5.35 x 5.35 inch

Speaker Audax HM130Z4, 8+8 ohm, 5.35 x 5.35 inch

drawing & mounting du cone driver Audax Speaker Audax HM130Z4, 8+8 ohm, 5.35 x 5.35 inch spl & impedance vs frequency measurement du cone driver Audax Speaker Audax HM130Z4, 8+8 ohm, 5.35 x 5.35 inch

Special availability
  • HD-A (High Definition Aerogel) cone. Non resonant die cast chassis. Ventilated chassis under spider. High loss, high compliance rubber suspension. Edgewound, flat copper wire. Kapton loss phase plus. Gold plated terminals.

    HD-A represents a true breakthrough in loudspeaker cone technology, surpassing all conventional materials being used today. Through an extraordinary combinaison of newly developed materials and process, Audax has created an innovative composite membrane whose properties are very close to ideal for making loudspeaker diaphragms. Ultra light, extremely rigid and maximized internal damping. This no-compromise cone is based on a totally controlled matrix of acrylic polymer gel in which an optimized proportion of Carbon and Kevlar fibers are embedded. An exclusive, proprietary process acts to perfectly align the fibers along the polymer chain. The procedure allows total control over the countour and weight of the cone, while making is possible to vary the thickness of the membrane along the profile. This 51/4-inch bass-midrange driver was developed for top range, no-compromise high-end 2 or 3-way systems. It features a die cast Zamck chassis with unobstructed venting for enhanced transient response and a non resonante phase plug for high end frequency equalization. High power handling resultats from the flat, edgewound copper coild mounted onto a fiberglass reinforced Kapton voice coil former. Unequaled definition is achieved aover a wide spectrum of frequencies and dynamic ranges while retaining a neutral tonal balance with precise detailed imaging.

  • Mid-Bass - Cone driver
  • 5 inch / 13 cm
  • Ferrite Ø85.8 mm
  • Non cylindrical
  • 136 mm x 152 mm
  • 6.8 mm
  • 60 mm
  • 8+8 ohm
  • Audax
  • Cone driver
  • 8+8 ohm
  • 1"
  • 91dB
  • 50W
  • 100W
  • 46Hz
  • 3ohm
  • 0.23
  • 5
  • 0.24
  • 10L
  • 80cm²
  • 3.3mm
  • 10gr
  • 0.3mH
  • 192
  • 1.1T
  • Zamack
  • Copper
  • Aerogel (HDA)
  • Kapton
  • 11.5 mm
  • mm
  • 6.2 L (tuned ar 75 Hz)
  • 1.3kg

... Display more



Question about Audax HM130Z4-8+8

Ask a new question!

This system is only available for technical questions. For questions of prices, availability of products and deadline thank you to send your request by the contact page of the website or following the procedure described on this page if it is a quote request.


Use Audax HM130Z4-8+8

This product list is manually managed by the TLHP team based on its experience and product knowledge.


With Audax HM130Z4-8+8, customers has also bought

This product list is automatically generated following the purchases from others customers.

Informations Audax HM130Z4-8+8

HD-A (High Definition Aerogel) cone. Non resonant die cast chassis. Ventilated chassis under spider. High loss, high compliance rubber suspension. Edgewound, flat copper wire. Kapton loss phase plus. Gold plated terminals.

HD-A represents a true breakthrough in loudspeaker cone technology, surpassing all conventional materials being used today. Through an extraordinary combinaison of newly developed materials and process, Audax has created an innovative composite membrane whose properties are very close to ideal for making loudspeaker diaphragms. Ultra light, extremely rigid and maximized internal damping. This no-compromise cone is based on a totally controlled matrix of acrylic polymer gel in which an optimized proportion of Carbon and Kevlar fibers are embedded. An exclusive, proprietary process acts to perfectly align the fibers along the polymer chain. The procedure allows total control over the countour and weight of the cone, while making is possible to vary the thickness of the membrane along the profile. This 51/4-inch bass-midrange driver was developed for top range, no-compromise high-end 2 or 3-way systems. It features a die cast Zamck chassis with unobstructed venting for enhanced transient response and a non resonante phase plug for high end frequency equalization. High power handling resultats from the flat, edgewound copper coild mounted onto a fiberglass reinforced Kapton voice coil former. Unequaled definition is achieved aover a wide spectrum of frequencies and dynamic ranges while retaining a neutral tonal balance with precise detailed imaging.
Product type Cone driver
Link manufacturer website Audax
Datasheet Internal link Audax
Transport weight 1.3 kg
Transport volume weight 0.71 kg

All or a part of the characteristics displayed on this page are provided by the manufacturer, it is possible that some pieces of information are unavailable or wrong. In addition, the manufacturer may need to change the product specifications without notice at any time in order to improve the product, or to adapt his offer to the manufacturing and supply constraints.. We suggest you to contact us if you need further information, if you observe a mistake or if you wish to have confirmation about information.

Measures/Schemes Audax HM130Z4-8+8

SPL & Impedance vs Frequency Measurement

Image spl & impedance vs frequency measurement cone driver Audax Speaker Audax HM130Z4, 8+8 ohm, 5.35 x 5.35 inch

Dimensions

Image Drawing & Mounting cone driver Audax Speaker Audax HM130Z4, 8+8 ohm, 5.35 x 5.35 inch


En poursuivant votre navigation sur ce site, vous acceptez l’utilisation de Cookies ou autres traceurs pour réaliser des statistiques de visites. En savoir plus
En poursuivant votre navigation sur ce site, vous acceptez l’utilisation de Cookies ou autres traceurs pour réaliser des statistiques de visites. En savoir plus